Part Number Hot Search : 
1C220 LB111 HV832 JF15CP2D 1B23A10 Y7C680 A393E BD136
Product Description
Full Text Search
 

To Download BPW049-0830-07CB95 Datasheet File

  If you can't view the Datasheet, Please click here to try to view without PDF Reader .  
 
 


  Datasheet File OCR Text:
 Ball / Land Grid Array Sockets Twist Lock Type
E-tec is now the leading BGA socket manufacturer.
EP patents 0829188, 0897655 US patents 6190181, 6249440 Patented in other countries.
Twist lock sockets are available for any chip size and grid pattern. The SMT socket is simply placed and reflowed onto the PCB in the same way as the chip and occupies only a small amount of additional board space. The 1.27mm pitch screw lock socket extends 6,00 mm beyond the outer ball row with no fixing holes. We aim to solve your requirements - many different terminals and configurations are available. Your custom sets our standards! Please note, we will always request the chip data to ensure we offer a compatible socket. SMT Style
Important Note: Please check the ball diameters & heights of your chip prior to ordering the standard E-tec BGA (BPW, BCW) sockets. Any deviation has to be communicated to E-tec in order to check compatibility with the standard socket design and if necessary to obtain a special order code adapted to your chip dimensions. The standard solderball diameters & heights are the following: Pitch ball diameters ball height min/max min/max 0.50mm 0.25mm / 0.35mm 0.15mm / 0.30mm 0.65mm 0.25mm / 0.45mm 0.15mm / 0.30mm 0.75mm 0.25mm / 0.45mm 0.15mm / 0.40mm 0.80mm 0.40mm / 0.55mm 0.25mm / 0.45mm 1.00mm 0.50mm / 0.70mm 0.30mm / 0.50mm 1.27mm & 1.50mm a) plastic chips (BPW) 0.60mm / 1.00mm 0.50mm / 0.70mm b) ceramic chips (BCW) 0.60mm / 1.00mm 0.80mm / 1.00mm If the minimum ball diameter of a given chip falls below the above indications, then a BUW socket will generally be proposed. Mechanical data Specifications
10.000 cycles min. 1.000 cycles min. exceeds MIL-STD-202 Method 208 40 grams max. up to 800 pins = 7cNm or 10 oz-inch as of 800 pins = 7cNm to 10cNm or 10 oz to 14 oz-inch High temp plastic or epoxy FR4 Brass BeCu
PCB Pad Layout
O 0,60mm/.024" if pitch 1,27mm O 0,50mm/.020" if pitch 1,00mm O 0,40mm/.016" if pitch 0,80mm O 0,35mm/.014" if pitch 0,75mm O 0,35mm/.014" if pitch 0,65mm O 0,30mm/.012" if pitch 0,50mm
You may request any specific socket dimension from info@e-tec.com For top view socket dimension pls. ref. to separate catalog page
Soldertail Style
Soldertail:
O 0,42mm/.016" O 0,29mm/.011" O 0,29mm/.011" O 0,27mm/.010" O 0,27mm/.010" O 0,27mm/.010" if pitch 1,27mm if pitch 1,00mm if pitch 0,80mm if pitch 0,75mm if pitch 0,65mm if pitch 0,50mm
Contact life Retention System life Solderability Individual contact force Max. torque for retention screws
Material
PCB Hole Layout PCB solder hole:
O 0,60mm/.024" O 0,50mm/.020" O 0,40mm/.016" O 0,35mm/.014" O 0,35mm/.014" O 0,35mm/.014" if pitch 1,27mm if pitch 1,00mm if pitch 0,80mm if pitch 0,75mm if pitch 0,65mm if pitch 0,50mm
Insulator (RoHS compliant) Terminal (RoHS compliant) Contact (RoHS compliant)
Electrical data
Contact resistance < 100 m Current rating 500 mA max. Insulation resistance at 500V DC 100 M if 0.50 to 0.80mm pitch 500 M 1.00mm pitch upwards 500V min. Breakdown voltage at 60 Hz < 1 pF Capacitance < 2 nH Inductance
Operating temperature
Torque limiting screw driver Solder paste Solder profile
-55C to +125C ; 260C for 60 sec.
Recommendations
The pitch dimension depends on your Ball Grid Array
Refer to page "Tools" of this catalog Please use a solder paste w/o any silver! Please refer to our website www.e-tec.com
X X W x x x x - x x x x - x x X X 95
Device Type
B = Ball Grid L = Land Grid C = Column Grid
How to order
L
optional for locating pegs
Device Material C = std. socket for P U
ceramic device
Pitch
05 06 07 08 = = = = 0,50mm 0,65mm 0,75mm 0,80mm 10 = 1,00mm 12 = 1,27mm 15 = 1,50mm
Grid Code Config Code
will be given by the factory after receipt of the chip datasheet
Plating
95 = tin/gold
(tin leadfree)
= std. socket for
plastic device
= socket adapted to
small diameter solderballs
others on request
Nbr of contacts
depends on ballcount of chip
30 29 28 70 = = = =
Contact Type
standard SMT...( A" = 1,20mm if 1,27mm pitch; 0,80mm if 1,00mm pitch, 0.60 if 0,80mm pitch; 0,40mm if <0.80mm pitch ) raised SMT..( A" = 5,00mm if 1,27mm pitch; 3,20mm if 1,00mm pitch; 2,80mm if 0,80mm pitch, 2.30mm if <0.80mm pitch ) special raised SMT - only for 1.00 & 0.80mm pitch........ ( A" = 4,50mm ) standard solder tail..................( A" = 3.30 if 1.27mm pitch, 2.80 if 1.00mm or 0.80mm pitch, 2,30mm if <0.80mm pitch )
8
Socket Mounting Recommendations and Reflow Profile
Purpose
This document is meant to serve as a guide for mounting E-tec surface mount device (SMD) sockets to the printed circuit board (PCB). The recommendations described here are guidelines only, and modifications may be needed for your particular socket, PCB, and process.
Application
The sockets this document applies to are as follows: Clam Shell, Knob Lock, Screw Lock, Twist Lock, Quick Lock and Lever Lock in SMD style. These sockets utilize the E-tec patented springpin technology. This technology allows the pins to be soldered to the PCB while still providing compliance to the device under test (DUT) via springs located at the other end of the pin. The pins themselves do not have solder pre-forms as a BGA would with its solder balls. However, the sockets are designed to mount to the same PCB footprint and pads as required by the BGA, or any other IC package the socket was designed for (except if locating pegs are used; see `Locating Pegs' section of this document). When compared to mounting a BGA, an extra volume of solder paste is required to mount the sockets to the PCB. To effect this, a properly dimensioned stencil is required. Once the paste has been applied, a standard reflow process is then used to solder the socket to the PCB. After the socket is verified to have proper electrical connection to the PCB, the system is then ready to be used.
Locating Pegs
Although designed to mount to the same footprint as the IC, with just a small amount of additional keep-out area, E-tec sockets can also be offered with locating pegs. The sockets are typically mounted with two locating pegs, which require two thru-holes drilled into the PCB. These pegs help to align the socket on the PCB, and hence align the socket's pins to the PCB's pads, during the soldering process. Furthermore, plating the thru-holes allows the locating pegs to be soldered to the PCB for better mechanical stability during everyday use and handling of the socket. If the PCB design permits, E-tec recommends the use of these locating pegs. For finepitch, low pin-count sockets without locating pegs, the mechanical strength of the solder joints may be insufficient. In these cases, it is recommended to epoxy the socket body to the PCB. 3M Scotch-Weld 2216 B/A is a suitable epoxy. In any case, the proper volume of solder paste is required to ensure mechanical and electrical integrity. Recommended stencil dimensions are given in the next section of this document.
E-tec Interconnect Ltd, Industrial Zone C, CH-1072 Forel (Lavaux), Switzerland Phone +41-21-781 08 10 * www.e-tec.com * info@e-tec.com
E-tec Socket Mounting Recommendations PRELIMINARY
1
Socket Mounting Recommendations and Reflow Profile
Stencil
Table 1 shows the recommended stencil dimensions. A laser-cut, electro-polished and Ni-plated stainless steel stencil is recommended to give the most consistent paste release. The apertures can be made round except for smaller pitches, where square apertures are recommended. Remember to keep the stencil small enough to fit within the keep-out area of the socket, but yet have provisions to remove it from the PCB once the paste has been applied.
Table 1: Recommended stencil dimensions.
Device Pitch (mm) 1.27 1.00 0.80 0.75 0.65 0.50
PCB Pad Diameter (mm / in) min. 0.60 / 0.023 min. 0.50 / 0.019 min. 0.40 / 0.016 min. 0.35 / 0.014 min. 0.35 / 0.014 min. 0.30 / 0.012
Stencil Thickness (mm/in) 0.15 / 0.006 0.15 / 0.006 0.13 / 0.005 0.13 / 0.005 0.13 / 0.005 0.13 / 0.005
Stencil Aperture (mm/in) round 0.66 / 0.026 round 0.55 / 0.022 round 0.44 / 0.017 square 0.39 / 0.015 square 0.39 / 0.015 square 0.33 / 0.013
Solder Paste
E-tec recommends using solder paste without ( or <0.5%) silver (Ag) to reduce the solder's wetting ability and prevent the paste from running up the pins, thus maximizing the volume of solder left on the pads. Brands such as Qualitek (www.qualitek.com) or Alpha Metals (www.alphametals.com) produce such solder paste on customer request. For Sn/Pb solder paste we recommend Ecorel 803S offered by Avantec (www.avantec.dehon.com).
Reflow Profile
Both standard Sn-Pb eutectic and Pb-free reflow profiles are shown below.
E-tec Interconnect Ltd, Industrial Zone C, CH-1072 Forel (Lavaux), Switzerland Phone +41-21-781 08 10 * www.e-tec.com * info@e-tec.com
E-tec Socket Mounting Recommendations PRELIMINARY
2
Socket Mounting Recommendations and Reflow Profile
E-tec Interconnect Ltd, Industrial Zone C, CH-1072 Forel (Lavaux), Switzerland Phone +41-21-781 08 10 * www.e-tec.com * info@e-tec.com
E-tec Socket Mounting Recommendations PRELIMINARY
3
Socket Mounting Recommendations and Reflow Profile
Verifying the Assembly
After the socket has been reflowed to the PCB, open and short testing should be partaken to ensure proper assembly. The assembly house typically performs x-ray inspection to verify nonshorting of pins. However, as this is only a visual inspection, we recommend using a continuity tester or ohmmeter and simply sweeping random rows and columns of pins to ensure no shorting of pins. No damage to the springs will occur if very slight pressure from the meter's tips is applied (just touch the probes to the springs). For fine pitch sockets, a microscope would be helpful in placing the meter's tips appropriately. After verifying the absence of shorts, open testing should be performed. The most direct, yet tedious, method is to use the continuity tester to directly probe each pin to a breakout or test point on the board. Again no damage will occur if the probes are touched to the springs. If heavy pressure is required to push the socket body towards the PCB to achieve continuity, this means a poor solder joint. If no such test points exist, then the BGA's via field on the backside of the PCB should be kept solder-mask free to allow for such probing. If the via field is kept open, a simpler open testing method can be performed. Simply use a wet sponge (or some other conductive material) and hold it onto the via field. This shorts all the pins together on the PCB. Insert one probe of the continuity tester into the sponge. Now sweep the pins of the socket with the other probe and check for continuity. If the above procedures show any shorts or opens, then it is advisable to have the assembly house re-evaluate the assembly method used. An incorrect stencil can lead to too much or too little solder paste, easily leading short or open conditions and a solder paste with Ag contents (>=0.5%) may also result in solder joint failures. These are the primary reasons for socket mounting failures.
Important Notes: a) Screw/Twist Lock Socket
When tightening the lid of a Screw or Twist Lock socket, it is imperative to not over-tighten the retention screws, otherwise irreparable damage may occur. Such damage is not covered by warranty and will be solely the end user's responsibility. The maximum allowed torque on these retention screws is 7cN-m (10oz-in) for sockets up to 800 pins and for sockets as of 800 pins the torque value needs to be increased but should not exceed a maximum of 10cN-m (14oz-in). E-tec sells the torque screwdriver TOL-7CN-TORQUE which is preset to 7cN-m, but which can be adjusted to higher torque values for the high pin count sockets.
E-tec Interconnect Ltd, Industrial Zone C, CH-1072 Forel (Lavaux), Switzerland Phone +41-21-781 08 10 * www.e-tec.com * info@e-tec.com
E-tec Socket Mounting Recommendations PRELIMINARY
4
Socket Mounting Recommendations and Reflow Profile
b) Knob Lock / Quick Lock / Clamshell Socket
It is recommended to remove the Knob Lock, Quick Lock and Clamshell retainer from the socket base prior to soldering the sockets to the PCB. This will avoid socket displacement during the soldering process due to the weight of these retainers. User instructions on how to remove and reassemble the Clamshell retainer from the socket base can be obtained from E-tec.
c) Pick & Place Pads
Pick & place pad options can be obtained on request for all SMT sockets. If required, please contact E-tec prior to placing a purchase order, since such pick & place pad options may require special fixtures on the socket base which are not included in the standard socket design.
E-tec Interconnect Ltd, Industrial Zone C, CH-1072 Forel (Lavaux), Switzerland Phone +41-21-781 08 10 * www.e-tec.com * info@e-tec.com
E-tec Socket Mounting Recommendations PRELIMINARY
5


▲Up To Search▲   

 
Price & Availability of BPW049-0830-07CB95

All Rights Reserved © IC-ON-LINE 2003 - 2022  

[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy]
Mirror Sites :  [www.datasheet.hk]   [www.maxim4u.com]  [www.ic-on-line.cn] [www.ic-on-line.com] [www.ic-on-line.net] [www.alldatasheet.com.cn] [www.gdcy.com]  [www.gdcy.net]


 . . . . .
  We use cookies to deliver the best possible web experience and assist with our advertising efforts. By continuing to use this site, you consent to the use of cookies. For more information on cookies, please take a look at our Privacy Policy. X